1.工作前穿戴好所規定的勞動用品，并認真檢查鍋爐給，排水，供氣管道附件，安全閥、壓力表、水位計是否靈敏好使，確認安全后，方可進行工作。
2.鍋爐水位標準水位不超過三分之二，水位不低于三分之一，一般情況，保持在1/2以上。
3.上水時要雙手操作，一手先開啟水門，隨之另一手開啟注水器汽門，水自然進入爐內。停止時，應先關閉汽門，然后關水門，在開關汽門時，臉部必須躲開正面，以免汽水沖出造成事故。
4.鍋爐在運行中，要注意檢查各部，觀察壓力和水位。如超壓或缺水時，必須停爐，將灰扒到前邊，稍稍注入冷水，但不準大量注入冷水，以免發生事故。
5.鍋爐在運行中，司爐工不準擅自離開崗位，夜班工作時，不準打瞌睡，更不準睡覺，以免發生事故。
6.鍋爐排污，每班必須進行一次，在排污前適當調整水位，稍微高2/3，然后進行排污。
7.水位表每班必須沖洗一次。沖洗時，要按規定程序，先關閉水閥，打開排污閥，沖洗汽閥，這時注意汽的來路是否堵塞。然后關閉汽閥，這時注意水的來路是否堵塞。沖洗水閥時，有水變汽為止，時間稍長些，才能保證不出假水位。
8.鍋爐用煤必須要檢查，防止煤中有雷管火藥等爆炸物品投入爐內，以防爆炸危險。
9.運行中要經常檢查機械設備和電動機外殼溫度，如機械有故障或電動機發熱超過60度，立即停機檢修。
10.鍋爐正常運行時，汽壓不得超過規定工作壓力，安全閥每周檢驗一次。

中譯英：
1 Work wear prescribed by the labor supplies, and carefully check the boiler, drainage, gas pipeline accessories, safety valve, pressure gauge, water level meter is a sensitive so to confirm the safety, we can work.
2 Boiler water level the highest level of not more than 2/3, the lowest level of not less than 1/3, in general, maintained above 1/2.
3 Sheung Shui to operate with two hands, one hand to open the gate, then the other hand open water valve, water enters the furnace. Stop, first close the valve, then close the Watergate, the switch valve, the face must avoid the positive, so as not to pop out accident.
4 Boiler in operation, pay attention to the inspection department, observing the pressure and water level. Such as super pressure or water, must stop furnace, grey chop to the front, slightly into the cold water, but not poured into cold water, to avoid accidents.
5 Boiler in operation, fireman to leave post, night work, not to doze off, but are not allowed to go to sleep, to avoid accidents.
6 Boiler blowdown, every class must have a, in sewage before proper adjustment of water level, slightly high 2/3, and then discharge.
7 Water level gauge in each class must be rinsed again. The flushing time, according to the provisions of procedure, to close the valve, open the drain valve, flushing valve, then pay attention to steam route is blocked. And then close the valve, then pay attention to the water source is blocked. Flushing water valve, water changes into steam, slightly longer, to ensure that no false water level.
8 Coal used by the boiler must check, prevent coal powder explosive detonator into the furnace, in order to prevent the risk of explosion.
9 Operation should always check the mechanical equipment and motor shell temperature, such as mechanical failure or motor fever over 60 degrees, immediately stop machine overhaul.
10 The normal operation of the boiler, the steam pressure shall not exceed the stipulated working pressure, safety valve inspection once a week.
(圖/文http://www.jnjrl.com/)